Flood Protection™ Starter Kit

Flood Protection Starter Kit includes: (1) 9oz Flex Paste® Flood Protection (Cartridge), recommended as your first layer of protection; and (1) 10oz Flex Seal Liquid® Flood Protection, recommended as final layer of protection. Also includes additional tools to make your job easier.

• Flood Protection Paste in a Cartridge is our primary Flood Protection product that should be used as a base coat for your first layer of protection. The precision nozzle that allows you to target specific areas that need to be sealed.

• Flood Protection Liquid should be used as a final coat of protection to help seal any small pinholes or openings that may have been missed.

• Once waters recede, both Flood Protection Paste and Liquid can be easily removed.

• Starter Kit Also Includes: (1) Caulking gun, (1) Gap Filler Tool, (1) 2" paint brush, (2) pairs of gloves, and our instructional How-to Guide.

For complete instructions, visit flexsealproducts.com/flood.

No water penetration through 1/2 inch gaps at depths up to 3 feet, for 14 days. UL Verified. VerifyUL.com. V114667.

We’re proud to say that when used in combination, and as directed, our Flood Protection Products have been independently verified by UL Solutions to hold back 3ft of water for 14 days on gaps up to ½ inch. Tested in laboratory settings.

Patent Pending for Products and Uses.

Buy more, save more. 5% off orders $500+, 10% off orders $2,500+, 15% off orders $10,000+, 20% off orders $20,000+. Applied at checkout, can not be combined with any other offer.
each
Flood Protection Starter Kit
No items found.

For more information or any questions, call our Customer Service Center at 833-4-A-FLOOD (833-423-5663)

Description
Directions
Videos
FAQs
International

PRODUCT DESCRIPTIONS

• Flood Protection Paste in a Cartridge starts out as a thick, paste that can be pushed deep into all types of openings and hard-to-reach areas. It dries to a strong, flexible, rubberized barrier. It seals out water, air, and moisture and remains flexible. Always push the Flood Paste into all seams and openings using a gloved finger, Flex Gap filler tool or similar tool. This will help create a watertight seal. Always be cautious of any sharp objects that may cause injury.

Flood Paste in a Cartridge is the primary Flood Protection product and should be used as a base coat for your first layer of protection. The cartridge nozzle allows you to target specific areas that need to be sealed. Use on windows, doors, garage doors, and all types of seams, casings, thresholds, conduits, vents and ducts, keyholes, and more.

• Flood Protection Liquid starts out as a liquid. It seeps into gaps, cracks and openings and dries to a strong, flexible, watertight, rubberized, coating. It blocks out water, air, and moisture, while remaining flexible. It helps seal any small pinholes or openings that may have been missed. Just brush a generous amount directly to the surface or over our other Flood Protection Products, making sure each coat is wider and overlaps the previous coat.

Flood Liquid should be used primarily as a final layer of protection to help seal any small pinholes or openings that may have been missed. Brush a generous amount directly on top of our other Flood Protection products. When applying Flood Liquid, make sure each coat is wider and overlaps previous layers of our Flood Protection products. Once floodwaters recede, both Flood Paste and Flood Liquid can be easily removed.

California Residents: Prop 65 Warning(s)

DRY TIME

Flood Protection Paste: Depending on temperature, humidity, and thickness of coating, Flood Paste will dry to the touch in in approximately 2 to 6 hours and fully cure in approximately 24-48 hours. Allow product to fully cure before floodwaters arrive. Always use fresh material to seal an opening.

Flood Protection Liquid: Depending on temperature, humidity, and thickness of coating Flood Liquid should dry to the touch in in approximately 3 to 6 hours and full cure in approximately 24-48 hours. When applying Flood Liquid, make sure each coat is wider and overlaps our other Flood Protection Products. Always use fresh material to seal an opening.

COVERAGE

Flood Protection Paste: A 1/4" inch bead will cover approximately 21 linear feet.

Flood Protection Liquid: At 2 inches wide, 10oz will cover approximately 18-22 linear feet at 15 mils thick.

IMPORTANT INFORMATION

Always follow state and local weather advisories and evacuation orders.

Depending on age and type of construction, there may be areas that cannot be seen or sealed.

Unsealed porous surfaces may seep water during extended underwater exposure.

Our Flood Protection products are NOT intended for flash floods, extreme winds or water pressure, to protect against flying or floating debris, or if there is structural damage to the building.

ADDITIONAL INFO

All of our Flood Protection products are Patent Pending for both products and uses.

Made in the USA with globally sourced materials.

Color of product is high-visibility yellow.

For more information on UL testing, click here.

For complete instructions go to: flexsealproducts.com/flood

Read entire label for directions and warnings before use.

• Protective gloves, clothing, andeyewear are recommended.

• Apply to the exterior of the structure.

• Area being sealed must be clean, dry, and free of grease, oil, and dirt.

Flood Protection Paste

• Unscrew nozzle, cut the nub on the cartridge, being careful not cut or damage threads.

• Screw nozzle back on cartridge and cut nozzle to the desired thickness of the bead.

• Place the cartridge into the caulking gun.

• Using a smooth motion, apply an even bead directly to the areas being sealed.

• Use your finger or tool to push the bead into the surface being sealed (gloves recommended).

• Apply additional coats after 2-6 hours or when dry to the touch.

• Additional coats should overlap and be wider than previous coats.

• Material can be tooled for approximately 10 to 15 minutes before curing begins.

• Allow approximately 24 to 48 hours to fully cure before floodwaters arrive.

Flood Protection Liquid

• Stir well before use, do not shake.

• Brush, roll, or pour several even coats anywhere water may enter.

• Apply additional coats after 3-6 hours or when dry to the touch.

• Additional coats should overlap and be wider than previous coats.

• Allow approximately 24 to 48 hours to fully cure before floodwaters arrive.

REMOVAL

Grab a small portion of material from an edge and pull away from the structure. Using a small pair of pliers may be necessary. If any residue is left on the surface, use a stiff nylon brush, paper towel or rag with denatured alcohol to clean the area.

THIS SECTION ONLY APPLIES TO FLEX FLOOD PROTECTION LINE


General Customer Questions International Distributors International Shipping Support